Wegner Dolphin Chair #14: Connecting Hardware

28
4

This is part 14 in a 14 part series: Wegner Dolphin Chair

  1. Four years later
...
  1. Backrest Assembly
  2. Connecting Hardware

A few installments back, I shared my hope that I would be able to weave the backrest assembly and seat/arm assembly independently and then connect the two assemblies together as the last step in construction.  This would have simplified the weaving process somewhat.   I ended up bagging the idea.   There were too many geometry issues of fitting things together at the last moment, and I couldn't 100% convince myself that I could manage it without issue.  Now the plan is to complete the two assemblies through to applying the finish, then connect them together, then weave.

My goal was to use some kind of fasteners that wouldn't be seen on the finished chair.   There will be four connectors, one at each point where the backrest stiles cross the arm and seat members.   I did some experiments with scraps using these Knapp connectors.   I'm sure I'll find a use for them, but they're not going to work for this project.   The little tab on them sits proud of the surface on at least on side of the joint, and I could just see me scratching up the just-finished chair frame while trying to hook everything together.


They do make a nice tight friction-fit joint if you get the installation just right.  I'm sure they'd hold a lot of weight.


Instead, I'm making some custom connectors that I can install after I've fit the finished backrest assembly inside of the seat/arm assembly.  I'm using 1/2" brass rod and some custom flanges I cut on the CNC.  The flange will be silver soldered to a short length of rod.  The rod will fit into a matching through-hole in the stile and into a blind hole in the seat/arm.  Three screws will hold the joint together tightly and the brass rod will carry all (or most) of the weight.





While the chair frame was dry fit together, I marked where the seat and arm crossed one of the stiles and used this as the reference stile.  With the stile removed, I located the center on the outward facing side.   Rather than carry the marks to the inward facing side, I drilled a 1/16" hole from the outside.


I'll use the 1/16" hole on the inside surface to locate the spur of the forstner bit to drill a shallow recess for the flange.




With the stile still clamped in place, I swapped the bit for a 1/2" forstner to drill a centered hole for the brass rod.





I stacked and aligned the two stiles and use a 1/2 brad point bit to mark the location for the hole on the other stile.


With the hole and recess completed for the stile/seat joint, I repeated the process for the seat/arm joint.



With the stile holes completed, I could then mark the locations for the holes in the seat and arms.  I checked measurements and level in a number of places on the chair to make sure everything was in the right position.  At this point, I just marked the location of the stile/seat holes.  I drilled blind holes for those first (as deep as I dared without the spur getting too close to the outer face).


I installed the rod for the seat joints, and then marked the hole location for the arm joint.



Time to fit it all together again with 4 short lengths of rod.  They're cut a little long so I have room to tweak the length after the flanges are soldered on.  I found it easiest to assemble the chair on its side.



The chair now standing on its own without props.  With the bar clamps to pull the mortise and tenon joints tight and prevent racking, I put a plank over the front and back seat stretchers and did a sit test.   I put my full weight on it, feet off the ground, and it felt very solid.



Next, I'm going to brick on some arm extensions to widen them and then sculpt them to the final shape.   It will be my first experience using a Kutzall on a grinder.   
one thing that always impresses me with your work is the precision and attention to detail ross. kutzalls are great but be careful you dont remove more than intended, DAMHIK !

working with my hands is a joy,it gives me a sense of fulfillment,somthing so many seek and so few find.-SAM MALOOF.

Wow, Ross! You’re approaching Jim Jakosh levels of jack-of-all-trade-iness with your custom brass hardware! That looks great!

I’ve never built a chair, but I would imagine that a full-weight sit test is a scary thing.
You might consider some flap disks for the grinder for fine turning the shape.  

--Nathan, TX. Hire the lazy man. He may not do as much work but that's because he will find a better way.

yes flap disc's are great for shaping and more gentle. but they can remove wood quit quick with low grits. i like a 80 grit disc after the rkutzall.

working with my hands is a joy,it gives me a sense of fulfillment,somthing so many seek and so few find.-SAM MALOOF.